Welcome to the Speakerbuilder.net discussion forum. While being polite and respectful is not common on the internet, please try not to flame people who don't deserve it. Otherwise, go nuts.
Hi,
Looking for a speaker design like the visaton vox series.
Really like this design;high tower with a small front and a bass-driver at the side;
The visaton speakers are way over my budget.
Only one I could find was the monacor prodomo:http://www.lautsprech...
This would be my first speaker building experience. I am wanting to build a 3-way floorstanding speaker with the following:
Adire AV5
Adire Extremis 6.8
Peerless 812978 1" tweeter
I was wondering if someone could help me with making a proper crossover for thi...
Good evening,
I have got parts ordered for a set of Dayton IIIs (my first speaker project) and I have a question or two about constructing and connecting the crossovers and drivers...
Since the hi- and low-pass sections of the crossover are shown separately fro...
I'm looking for a good set of speakers for a small office, 12' x 13'. I'll be playing mostly classic rock, blues, electric folk, a little bit of classical. I'm a musician/music lover as opposed to an audiophile - meaning I appreciate good sound but "good" is good e...
I am considering building a set of Eros and was wondering if there is anyone in the Windsor to Toronto corridor that has built a set I could listen to. I would be greatful to anyone generous enough to let me listen to their speakers. thank you, Paul
Has anyone got pictures of their completed eros 2 crossover they could send out...My constructuion is completed however I am better with woodwork than electronics and a visual would help me out..douglasbrown@shaw.ca
I recently built a pair of Lyra speakers.(They sound GREAT!) I noticed that one of the drivers could handle 50 watts RMS. Might this be a problem with an amp that is capable of 70 watts RMS?
any problem with making the enclosure front baffles out of 3/4" MDF and then using 1" MDF for the rest of the enclosure...the net loss of thickness would only be 1/4" and be much less labor intensive...i am wondering if the sonic quality would be comparable...dko
I am about to venture to build my first set of speakers. Not sure which yet but had a question regarding the stuffing wool stuff. When a internal volume is defined for a type of speakers and a box can be built as long as internal volume is what is stated, when you...
I should have asked this question on my first post about the Lyra/xover/inductors. There is a 60uf cap shown on the low pass. Should I use a 60 npe or go for a combination of 60 with a higher quality cap. I have only built one pair of diy speakers. I would really lik...
I am gathering parts for Wayne J's Lyra project. Would it be ok to use the Jantzen 15 gauge air core inductors in place of the 16 gauge on the crossover? Same value of course. Thanks All.
Hey i have 2 towers that im looking to put new speakers into. How hard would this be and what type of speakers are best to put in these towers? Im looking for speakers that do superior audio for music as well as superior audio for movies.
The box has 1 tweeter 1 4...
This will be my first project and the construction of the speaker is not well documented. The link is located http://www.wadsnet.com/~dtenney/dayton_8MTM.htm
Can anyone help me figure this project out? I need to know how to construct the cabinet and also the speak...
I like my Spendor S3/5 speakers except for the cabinet, which rings like a bell. I've tried some simple tweaks like placing a bag of lead shot on top. I would like to try a more dramatic tweak, and I was wondering if anyone has ever tried something similar.
Basica...
I lost my woodshop space in my last move, so i need to pay someone to build some cabinets for my Seas Excel / Hiquphon 3-way. I have the basic design done, but am open to suggestions. I am not particularly picky about fine finish details. i would be very grateful...
I am building the Eros speakers and do not have the ideal place to put them for the best sound. They will be close to a wall which might cause the base response to not be ideal.
My Question is: Can I place the port in the front baffel instead of in the back as th...
Are there are any methods for calibrating a microphone? I'm not looking forward to spending money mainly because I don't have any. I made a DIY microphone out of an electret element; although the electret isn't the Panasonic brand that every DIY webpage recommends. I...
does anyone have ideas on better woofers for sl-700's?they can't take the low end when watching movies,6" drivers,7" diagonal from screw hole to screw hole,can anyone help?
for the enclosures there have been two approaches
1) 3/4"mdf bonded with 1/2" plywood; or
2) 2 layers of 3/4" mdf bonded together
- can you tell me the pros and cons of each method suggested?